Custom Engeneering PLUS II Bedienungsanleitung

OEMUSER MANUALPLUS IIPLUS IICommand Reference: DOMC-0009e

UNPACKING THE PRINTERRemove the printer from its carton being careful not to damage the packing material so that it may be re-used if the printer is t

GENERAL FEATURESPLUS II is the new ultra-compact thermal panel printer, paper width 57,5 mm, with “SIXLOAD” easy paper loading system. PLUS II is perf

• FEED key When the LINE FEED key is pressed (see fi g.4), the printer advances the paper. During power-up, if the FEED key is held down, the printer

• STATUS led displays printer hardware status. In case of malfunction, the fl ash frequency changes as shown in Tab.1 for models with USB interface a

Blank pageINTRODUCTION6 PLUS II User Manual

1.1 PAPER SPECIFICATIONSPrinter manage thermal roll (heat-sensitive side on outside of roll) or LINERLESS paper (see paragraph 1.1.1).1.1.1 Specifi cat

WARNINGDo not set “Printer Density” parameter on “Linerless” mode during the printer SETUP (see par.1.8) with common thermal paper!ATTENZIONEIn “Liner

1.2 CONNECTIONS OF PLUS II-S AND PLUS II-T1.2.1 Power supplyThe printer is equipped with a 4 pin JST male connector (90°) for the power supply. The s

1.2.2 Setting serial interfaceThe JP4, JP5, JP6 and JP7 jumpers on controller board (see Fig.1.4) manages the setting of serial interface as indicated

1.3 CONNECTIONS OF PLUS II-S-00041.3.1 Power supplyThe printer is equipped with a 2 pin male connector terminal block (90°) for the power supply. The

All rights reserved. Total or partial reproduction of this manual in whatever form, whether by printed or elec-tronic means, is forbidden. While guara

1.3.2 Setting serial interfaceSee paragraph 1.2.2.1.3.3 Power-On confi gurationThe JP8 jumper on controller board (see Fig.1.6) manages the power-on se

1.4 CONNECTIONS OF PLUS II-C AND PLUS II-P1.4.1 Power supplyThe printer is equipped with a 4 pin JST male connector (90°) for the power supply. The si

1.4.2 Setting serial interfaceThe JP2 and JP1 jumpers on controller board (see Fig.1.8) manages the setting of parallel interface as indicated:JP1 JP2

1.5 CONNECTIONS OF PLUS II-C-00041.5.1 Power supplyThe printer is equipped with a 2 pin male connector terminal block (90°) for the power supply. The

1.5.2 Setting serial interfaceSee paragraph 1.4.2.1.5.3 Power-On confi gurationThe JP5 and JP6 jumpers on controller board (see Fig.1.10) manages the s

1.6 CONNECTIONS OF PLUS II-USB1.6.1 Power supplyThe printer is equipped with a 2 pin male connector terminal block (90°) for the power supply. The si

1.7 SELF-TESTPrinter operating status is indicated in the confi guration report in which, next to the name of the components displayed (see fi g.1.12, fi

1.8 CONFIGURATIONPLUS II permits the confi guration of default parameters.The confi gurable parameters for PLUS II-S, PLUS II-S-0004 and PLUS II-T model

1.9 HEXADECIMAL DUMPThis function is used to display the characters received from the com-munications port; after the reception of each 8 characters f

23 4(Fig.1.20)(Fig.1.19)(Fig.1.18)1. INSTALLATION AND USEUser Manual PLUS II 1-15

PRINTER COMPONENTSA. PLUS II - Front view1 - STATUS Led2 - Paper roll compartment3 - Paper mouth4 - OPEN key5 - FEED key5431212PLUS II412531212PLUS II

5 61.10.2 Notes about the installationFixing to the panelFix the printer in the 3 holes as shown in the scheme (A) (see fi g.1.23), using M3 tapping sc

1.10.3 “EASYLOCK” fi xing systemThis system allows to adapt the printer to every panel thickness and it is not necessary to use other fi xing tools.A FI

Blank page1. INSTALLATION AND USE1-18 PLUS II User Manual

2.1 INTERFACE OF PLUS II-S AND PLUS II-TThe printer with a serial RS232/TTL interface has a molex 6-pin male connector 53261 series (90°). Refer to th

2.1.1 Connection Printer-PCThe diagrams below show a sample connection between printer and Personal Computer using a 6 pin female Molex 51021 connect

XON/XOFF ProtocolDATARDSTOPSTART BIT START BITSTOPDATAWAIT$13XOFFTDSTOPSTART BIT START BITSTOP$11XON2. INTERFACESUser Manual PLUS II 2-3

2.2 INTERFACE OF PLUS II-S-0004The printer with RS232 interface has a 6-pin male connector AMP-MODU II (90°). Refer to the table below for the connect

2.2.1 Connection Printer-PCThe diagrams below show a sample connection between printer and Personal Computer using a 6 pin fe-male AMP MOUD II connect

2.3 INTERFACE OF PLUS II-C AND PLUS II-PThe printer with parallel Centronics/TTL interface has a molex 15-pin male connector 53261 series (90°). Refer

2.3.1 Connection Printer-PCThe following scheme, represent the connection cable confi guration between Molex connector 51021 series 15-pin (female) and

B. PLUS II - Rear view1 - Power supply connector2 - RS232 / TTL serial interface connector3 - CENTRONICS / TTL parallel interface connector4 - USB int

For parallel TTL interface printer the communication signals are: 8 bit DATA BUS, STROBE (indicate the data validity) and BUSY (indicate that the prin

2.4 INTERFACES OF PLUSII-C-0004The printer with a parallel Centronics interface, 0004 option, has a molex 15-pin male connector 53261 series (90°). Re

2.4.1 Connection Printer-PCThe following scheme, represent the connection cable confi guration between Molex connector 51021 series 15-pin (female) and

2.5 INTERFACES OF PLUS II-USB2.5.1 USB interfaceThe printer is provided with a 6-pin male connector AMP-MODU II (90°). Refer to the table below for th

2.5.2 RS232 serial interfaceThe printer is provided with a molex 6-pin male connector 53261 series (90°).This interface is RESERVED only to service us

3.1 TECHNICAL SPECIFICATIONSTable 3.1 gives the main technical specifi cations for the printer.Available interfacesPLUS II-S, PLUS II-S-0004, PLUS II-T

Table 3.2 gives the printing specifi cations for the PLUS II-S, PLUS II-S-0004, PLUS II-T, PLUS II-C, PLUS II-C-0004, PLUS II-P.PRINTER SPECIFICATIONSP

Table 3.4 gives the electrical specifi cations for the PLUS II-S, PLUS II-S-0004, PLUS II-T, PLUS II-C, PLUS II-C-0004, PLUS II-P.ELECTRICAL CONDITIONS

3.2 DIMENSIONSThe fi g 3.1 shows the dimensions for PLUS II.MOUNTING SEAT IN THE PANNEL85.589818581.511111571,843,24590°10.113.1 10.4Versions:PLUS II-C

The fi g 3.2 shows the dimensions for PLUS II (OPTION -0128).81,5+0,5-0,5 max panel thickness 385,5+0,5-0,582+0,5-0,582+0,5-0,545+0,5-0,511+0,5-0,59011

1 4 5PLUS II-USBNOTE (1) : RESERVED interface, only for service use.(Fig.7) User Manual PLUS II

Blank page3. TECHNICAL SPECIFICATIONS3-6 PLUS II User Manual

4.1 CHARACTER SETS4.1.1 Character sets for PLUS II-S, PLUS II-S, PLUS II-T, PLUS II-C, PLUS II-TThe printer has 2 fonts each width 224 characters (Fon

4.1.2 Character sets for PLUS II-USBThe printer has 2 fonts of varying width (12, 17 and 22 cpi) which may be accessed through programming or control

A.1 ACCESSORIESA.1.1 Power supplyThe fi g.A.1 illustrates the power supply provided by Custom to be used for printer operation of PLUS II-S, PLUS II-S-

The fi g.A.2 illustrates the power supply provided by Custom to be used for printer operation of PLUS II-USB. The tab.A.2 gives the main technical spec

A.1.2 Adaptor frame kit 112X112An adaptor frame is available for all the PLUS II models. It makes PLUS II mechanically compatible with CUS-TOM F and P

Assembling instructions Fit the printer (A) into the adaptor frame (B), making sure that the side of the printer with carter gears (C) • is aligned wi

The fi g.A.8 illustrates the dimensions of PLUS II models assembled with the frame.35119123.21125011917,490°11226.311139.5Mounting seat in the panelN °

A.1.3 Data and power supply cables kit for PLUS II-S and PLUS II-TThe printer can be supplied with a data and power supply cables starter kit.PCSKPLUS

A.1.4 Data serial cable kit for PLUS II-S-0004The printer can be supplied with a data serial cable (see fi g.A.11).PCSKPLUS-0004 Starter kit cables for

C. PLUS II - Internal view1 - Printing head2 - Rubbed roller3 - Seat for fi xing hook (provided in the package)4 - Paper presence sensor5 - Cover open

A.1.5 Data and power supply cables kit for PLUS II-C and PLUS II-PThe printer can be supplied with a data and power supply cables starter kit.PCSKPLUS

A.1.6 Data parallel cable kit for PLUS II-C-0004The printer can be supplied with a data parallel cable (see fi g.A.15).PCSKPLUS-C-0004 Starter kit cabl

A.2 SPARE PARTSA.2.1 SuppliesRCT57X50Thermal paper roll 57mm d=50Quantity recommended per n° machines purchasedN° machines <10 <50 <100 >

Part Number : DOME-PLUSII Rev. 1.25www.custom.bizCUSTOM ENGINEERING SPAWorld HeadquartersVia Berettine, 2 - 43010 Fontevivo, Parma ITALYTel. +39 0

INTRODUCTIONMANUAL CONTENTS ...

2. INTERFACES2.1 INTERFACE OF PLUS II-S AND PLUS II-T .......2-12

MANUAL CONTENTSIn addition to the Introduction which includes a description of the explanatory notes used in the manual, general safety information, h